Waterproofing Resin - Poligold Cimar - Colored Elastic Polyurethane
Poligold Cimar is an
elastic and colored polyurethane waterproofing sheath .
The liquid resin Poligold is a
breathable and walkable product, it offers greater resistance to adverse climatic conditions and to the hot / cold cycle.
- It maintains its properties unaltered from + 80 ° C to -20 ° C.
- Resists water stagnation;
- It guarantees a minimum duration of 7 years; with a further coat of product a further 5 years are guaranteed;
- On supports such as wood and concrete it guarantees natural transpiration;
- Choice of colors (select the variant).
Features and uses polyurethane liquid sheath
Very fast drying
liquid waterproofing in aqueous emulsion; based on hybrid polyurethane acrylic resins and nanoparticle fillers that give the sheath greater durability outside.
Poligold Cimar resists water stagnation. It is used to waterproof any type of substrate: restoration of terraces, viaducts, deteriorated bituminous membranes, metal sheets, plasters and retaining walls.
- Single component and ready to use.
- Easy application;
- Resists stagnant water;
- It maintains its properties unaltered from -20 ° to + 80 ° C;
- In case of accidental breakage, it can be easily repaired in a few minutes;
- Monolithic product without welding;
- Permeable to water vapor;
- Resists ultraviolet rays, yellowing and atmospheric agents, does not require protection;
- Walkable, non-toxic coating.
Characteristics of identification of the liquid product
- Appearance: Viscose pigmented paste
- Specific weight = 1.3 ± 0.05 Kg / dm3
- Dry residue = 60 ± 5%
- VOC content as required by the legislative decree of 27/05/2006 n ° 161: 140 g / l of ready-to-use product
- VOC content in the product: 60 g / l of ready-to-use product
Primer
The primer to be used for both cementitious systems, bricks, stone, tiles, wood and bituminous sheath is always the same; POLIGOLD diluted with 20% of water. Apply in one coat with a consumption of 300 g / m2. The complete apparent drying time of the primer at a temperature of 23 ° C and 50% RH is 3h.
Equipment
Apply by roller, brush or spray (airless with pressure> 220 bar flow rate> 5.1 L / min Ø nozzle> 0.83 mm). Clean the equipment immediately after use with water. Hardened product can only be removed mechanically.
Reinforcement
The reinforcement to be used for POLIGOLD is a POTENZIO non-woven polyester fabric supplied by Cimar.
Application support
Cement-based substrate: the concrete must have cured at least 28 days and must have a tensile strength ≥1.5 MPa. Any traces of material that tends to detach must be removed and the surface must be the most
can be adjusted by eliminating roughness by abrasion.
- Tiles: they must be well adherent and not damaged. Porcelain or glass tiles must be made porous by abrasion and treated with primer.
- Deteriorated bituminous membrane: the roll must be well adherent and there must be no loose parts otherwise they will need to be repaired.
- Metal and Wood: the surfaces must be healthy and intact. Use the primer and POTENZIO Reinforcement Fabric in the joints and fasteners.
Consumption
Consumption depends on the porosity and regularity of the surface. It is estimated at ca. 2 Kg / m2 in two or three coats.
This consumption is based on roller application on a smooth surface under optimal conditions. Factors such as surface porosity, method of application and temperature can alter consumption.
Buy the best professional waterproofing products online
The Cimar company
produces a large variety of
professional waterproofing products in Italy.
For more than 20 years this Italian company has been active in the research of modern products in the building waterproofing sector.
